limit ratio
英 [ˈlɪmɪt ˈreɪʃiəʊ]
美 [ˈlɪmɪt ˈreɪʃioʊ]
限辐比（峰值与极限值之比）
双语例句
- And it is proved that it can reach smaller limit drawing ratio by the deep drawing experiments.
通过拉深工艺试验证明该曲面凹模可以达到很小的极限拉深系数。 - Random sequence Random limit logarithmic likelihood ratio Random approximation theorem Random selection Two-order Markov distribution Stochastic dominated sequence.
随机序列随机极限对数似然比随机逼近定理随机选择二重马氏分布机控制序列。 - The express-method of the limit drawing ratio evaluation is presented.
列出了确定极限拉伸系数的快速方法。 - Determination of the Limit Drawing Ratio of Tapered Cup
锥形件极限拉深比的确定 - In this paper, the elasto-plastic buckling of simply supported aluminum alloy plates is analyzed and the limit ratio of wide-to-thickness between elastic buckling and elasto-plastic buckling is obtained.
采用有限元方法分析了四边简支铝合金板的弹塑性屈曲，得出了铝合金板弹性屈曲与弹塑性屈曲之间的临界宽厚比。 - Analysis of Effect of Vertical Motion on the Limit Ratio of Height to Width of Base Isolated Structures
竖向地震动对隔震结构高宽比限值的影响分析 - In addition, the reasonable limit of reserve-production ratio when production decline occurs is researched.
应用递减方程研究了油气藏递减时储采比的合理界限。 - It is also found that there exists a maximum isolation period, at which, the limit ratio is zero or the horizontal displacement of the rubber bearing exceeds the allowable value.
研究还发现，存在一个最大的隔震结构周期使高宽比限值等于零或隔震层位移超过容许值。 - Study on the Technology and Limit Drawing Ratio of Magnesium sheet Stamping
镁合金板材冲压成形工艺及极限拉延比研究 - In thermodynamic limit the ratio of the number of states involved in the most probable distribution to all possible states accessible to the system is zero.
通过对一个简单模型的研究可知，最概然分布包含的微观状态数和全部可能微观状态数的比值在热力学极限下为零。 - This criterion can be used to study the quantative influence of the properties of working materials and the technological parameters on the limit drawing ratio ( m_k).
该判据可用于定量研究材质和成形工艺参数对极限拉深系数mk值的影响。 - The paper obtains the critical buckling stress of web with circular opening subjected to shear and bending separately and the corresponding limit of depth-thickness ratio.
本文作者研究了开有圆孔的腹板在剪切、弯矩单独作用下的屈曲应力以及相应的腹板高厚比限值。 - The upper limit of the ratio of Monte Carlo estimated error to averaged value is about 0.3%.
蒙特卡罗估计误差与平均值比值的上限小于0.3%。 - The curves and data of limit drawing ratio, which can be applied in production, are given.
文中给出的锥形件一次拉深成形极限拉深比图线和数表，可供生产实用。 - Within the limit of ratio of zero principle tensile stress to optimal stress of concrete, the range of rational vertical prestress values is determined and design procedures for the prestress are provided.
以不出现主拉应力和最佳应力比为界限，确定合理竖向预应力值的范围，并给出竖向预应力设计步骤。 - Limit of stress ratio of the members is determined and member optimization calculation is made by taking into full consideration various factors such as the importance of the project, the loading feature of the structure, and construction error and project cost.
在综合考虑工程的重要性、结构受力特点、施工偏差以及工程造价等多种因素的基础上确定构件应力比限值，进行构件优化计算。 - Limit amplitude ratio of coherent light to obtain distinct interference patterns
获得清晰干涉图样的相干光极限振幅比 - The system is composed of speed pulse test and reshaping circuit, logic control circuit, STD industrial control machine, setting circuit for limit of speed ratio, counter and control circuit, genesis circuit for simulating pulse.
系统的硬件组成包括速度脉冲检测与整形电路、逻辑控制电路、STD工业控制机、速度比上下限设定电路、计数器及其控制电路、模拟脉冲发生电路； - The experimental results show that the calculated value ( m_k) of the limit drawing ratio is credible and the suitability of this criterion proposed is very well.
试验结果表明：该判据确定的极限拉深系数mk值准确，且其适用性强。 - Reasonable limit of ratio of reserves to production and prediction of production decline trend
油田储采比合理界限与产量递减的趋势预测 - The equations for determining the limit opening ratio, one for flow with mild slope and one for steep slope, are deduced based on the principle of energy conservation and continuity.
根据能量守恒和水流连续方程，建立了缓坡及陡坡条件下卡克水流的临界判别条件。 - From the balance of ash and carbon to calculate ash coefficient needed by the boiler thermal calculation, the limit circulation ratio was definited.
从灰平衡、碳平衡出发，求得锅炉热力计算所必需的灰系数，确定极限循环倍率； - Analyzes and compares the performance of plastic and steel products under light load drive and calculates the probably reached limit of drive ratio for both types of flexsplines under the same load;
分析比较了轻载传动情况下塑料和钢材的性能，计算了塑料制谐波柔轮和钢制谐波柔轮在相同载荷情况下可能达到的传动比极限； - The notion of limit relative log-likelihood ratio is introduced to investigate the limit properties of the sequence of dependent discrete random variables.
引入极限相对对数似然比的概念，作为离散相依随机变量序列与独立随机变量序列的偏差的一种度量，并利用它来研究离散相依随机变量序列的极限性质。 - By comparing the isolation period with the critical and maximum periods, the limit ratio can be obtained by using the corresponding formulas.
将隔震结构的周期与临界周期和最大隔震周期比较，就可以得到相应高宽比限值的表达式。 - We believed that from the analysis the currently oil reserve-production ratio is far below the stable limit reserve-production ratio, the rapidly declining oil production is a concrete manifestation of the normal development law in oil fields.
分析认为塔中4油田目前储采比远低于稳产极限储采比，油田产量快速递减是油田正常开发规律的具体体现。 - Therefore, the steel must be yielded before ductile failure in the design. ( 4) Material requirement is controlled by limit ratio of CFRP satisfying ductility.
因此，加固设计需保证加固梁破坏之前钢筋已经屈服。（4）采用满足延性要求的界限配布率控制碳纤维布用量。 - Therefore, a method of decomposing human body silhouette is put forward. In this method, body silhouette is primarily divided into segmentations depends on the negative curvature extreme points, under the limit of the ratio between arc length and secant line.
该方法依据人体轮廓上的负曲率极值点，在轮廓弧长与割线比值的限定下，对人体轮廓进行初步分解。 - By introducing the conception of ballistic limit mass ratio, the executions of non-spherical projectiles are made a qualitative comparison with that of spherical projectiles.
通过引入弹道极限质量比的概念，定量地比较了非球形弹丸和等效直径球形弹丸破坏能力的大小。 - The influences of the gap of mould, the grain size and drawing ratio on the quality of micro drawn cup is studied. And the influences of the gap of mould and the grain size on limit drawing ratio is also researched.
研究了模具间隙、晶粒尺寸和拉深比对黄铜箔微圆筒拉深件成形质量的影响规律，以及模具间隙和晶粒尺寸对极限拉深比的影响规律。